| skullbrain.org http://skullbrain.org/legacy/ |
|
| Mold Release problems http://skullbrain.org/legacy/viewtopic.php?f=49&t=41232 |
Page 1 of 1 |
| Author: | computerhair415 [ Tue Dec 06, 2011 12:21 am ] |
| Post subject: | Mold Release problems |
What is the best way to clean up mold release off resins after its set? I have noticed that sometimes paint has trouble staying on and I figure its because the mold release. Also when I do the clear resin it can dull or mess with the clarity. Any folks out there have any tips? I want to make eyes 
|
|
| Author: | evom [ Tue Dec 06, 2011 5:55 am ] |
| Post subject: | Re: Mold Release problems |
I wipe mine down with alcohol. It seems to work pretty good. and if you gloss clear coat foggy resin it'll make it very clear. |
|
| Author: | ButcherBrand [ Wed Dec 07, 2011 7:58 am ] |
| Post subject: | Re: Mold Release problems |
Mild soap and water also. alcohol sounds good ill have to try it. |
|
| Author: | dedoperucelli [ Wed Dec 07, 2011 3:49 pm ] |
| Post subject: | Re: Mold Release problems |
I use alcool |
|
| Author: | michael [ Wed Dec 07, 2011 5:22 pm ] |
| Post subject: | Re: Mold Release problems |
hot water, soap, and a tooth brush scrub! got this info recently and it works well |
|
| Author: | mondocoyote [ Wed Dec 07, 2011 5:42 pm ] |
| Post subject: | Re: Mold Release problems |
I use Dishwashing soap with a soft scouring pad/ sponge, rinse, then dip into ethanol and scrub with a toothpaste. Possibly overkill, but making up for my earlier laxness! |
|
| Author: | computerhair415 [ Thu Dec 08, 2011 11:18 pm ] |
| Post subject: | Re: Mold Release problems |
Thanks for all the info folks. Im definitely going to check them out. Im trying to make some eyes and I want them to be as clear as possible. keep ya updated. |
|
| Author: | ButcherBrand [ Fri Dec 09, 2011 6:35 am ] |
| Post subject: | Re: Mold Release problems |
computerhair415 wrote: Thanks for all the info folks. Im definitely going to check them out. Im trying to make some eyes and I want them to be as clear as possible. keep ya updated. Good luck man. I would love to see what you come up with. Post some pics when you are done. |
|
| Author: | uh oh [ Sat Dec 10, 2011 2:01 am ] |
| Post subject: | Re: Mold Release problems |
mondocoyote wrote: I use Dishwashing soap with a soft scouring pad/ sponge, rinse, then dip into ethanol and scrub with a toothpaste. Possibly overkill, but making up for my earlier laxness! I hope you meant a toothbrush Brian. |
|
| Author: | mondocoyote [ Sat Dec 10, 2011 2:06 am ] |
| Post subject: | Re: Mold Release problems |
uh oh wrote: mondocoyote wrote: I use Dishwashing soap with a soft scouring pad/ sponge, rinse, then dip into ethanol and scrub with a toothpaste. Possibly overkill, but making up for my earlier laxness! I hope you meant a toothbrush Brian. I did say it was probably overkill...  yeah... Toothbrush 
|
|
| Author: | computerhair415 [ Sat Dec 10, 2011 8:40 am ] |
| Post subject: | Re: Mold Release problems |
mondocoyote wrote: uh oh wrote: mondocoyote wrote: I use Dishwashing soap with a soft scouring pad/ sponge, rinse, then dip into ethanol and scrub with a toothpaste. Possibly overkill, but making up for my earlier laxness! I hope you meant a toothbrush Brian. I did say it was probably overkill... yeah... Toothbrush now ya tell me ....... Iv been scrubbing toothpaste all over my resins..  
|
|
| Author: | uh oh [ Sat Dec 24, 2011 11:00 pm ] |
| Post subject: | Re: Mold Release problems |
I've been wondering for a long time if a ultrasonic cleaner would work. |
|
| Page 1 of 1 | All times are UTC - 8 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|