ANNOUNCEMENT:
There will be some planned downtime starting Wednesday, June 15th at 9am EDT. The board will be closed for approximately 12 to 24 hours while we work on migrating to a new forum software. For more information on the move, check out the Board Change Announcements thread.
|
|
|
|
It is currently Sun Dec 22, 2024 8:55 pm
|
View unanswered posts | View active topics
 
|
Page 1 of 1
|
[ 9 posts ] |
|
| Author |
Message |
|
ribbon controller
S7 Royalty
Joined: Mon Feb 12, 2007 2:25 am
Posts: 3494
Location: Earth
|
 Airbrush cleaning so I have a problem with my airbrushes not working after having cleaned them very well .. somehow they blast air thru them while empty.. but once i pour some paint in..it just bubbles in the cup instead of spraying out.. I have repeatedly cleaned them after and even changed out needles.. ..but the same result keeps happening.. can't figure it out.. about to just send them off to iwata
anyone else experience this?
|
| Sat Jul 19, 2014 2:18 pm |
 
|
|
|
evom
S7 Royalty
Joined: Mon May 31, 2010 12:28 am
Posts: 3581
|
Re: Airbrush cleaning not thin enough paint? not enough psi..?
did you fully take it apart. it breaks down pretty far.
_________________
WANTED:BUTANOHANA / Gargamel
|
| Sat Jul 19, 2014 2:29 pm |
|
|
|
IronPaw
Comment King
Joined: Sat Sep 08, 2012 11:53 pm
Posts: 1332
Location: Los Angeles
|
Re: Airbrush cleaning Have you tried cleaning the cups spout? Are you using the standard Iwata side cup? That one is really annoying to clean out and clogs easily
because of the way it moves the paint into the airbrush.
_________________
Winu wrote: I propose a petition to ban everyone.
|
| Sat Jul 19, 2014 2:30 pm |
|
|
|
ribbon controller
S7 Royalty
Joined: Mon Feb 12, 2007 2:25 am
Posts: 3494
Location: Earth
|
Re: Airbrush cleaning I have 3 brushes all iwata 2 eclipses and 1 neo and i have the same problem with all of them.. i have taken them completely apart and soaked and cleaned them very well..this just recently happened..
|
| Sat Jul 19, 2014 3:21 pm |
|
|
|
badteethcomics
Comment King
Joined: Fri May 31, 2013 10:32 pm
Posts: 1296
Location: Brisbane, Australia
|
Re: Airbrush cleaning Hmmm if it's happening with all of your brushes it sounds like it could be what you're using to clean them with.. What type of paint are you using and what thinner/cleaner? And how do you go about cleaning your brushes after a session?
_________________
BTC - http://www.badteethcomics.com
Blog - http://www.instagram.com/badteethcomics
Top 5 Toys - http://top5toys.blogspot.com
SVM - http://softvinylmayhem.com/
----------------------------------------------------------------
Wants - http://skullbrain.org/bb/viewtopic.php?f=26&t=49396
|
| Sat Jul 19, 2014 4:07 pm |
|
|
|
dtoes
Toy Prince
Joined: Tue Apr 15, 2014 5:23 pm
Posts: 401
|
Re: Airbrush cleaning If you are using iwata eclipse, there should be a small piece that sits inside the tip that the needle goes through. This is where most of the clogs happen, go in with something as sharp and thin as the needle and push all the paint that is stuck in there out. Usually opaque paints/thicker paints get clogged up in that area. Then run some warm water/hot water over is and blow into it. If you can see light at the other end you might be back in business.
Sometimes it could also be how you put your brush back together. Not tightening enough etc. hope this helps!
|
| Sat Jul 19, 2014 5:08 pm |
|
|
|
Rich
Die-Cast
Joined: Tue Mar 07, 2006 8:46 pm
Posts: 11806
|
Re: Airbrush cleaning It's the little metal tip inside where the needle exits. Get that little wrench tool it comes with and tighten it up. Should fix it.
|
| Mon Jul 21, 2014 3:58 pm |
|
|
|
gatchabert
Prototype
Joined: Mon Aug 06, 2007 11:41 pm
Posts: 6389
Location: 415
|
Re: Airbrush cleaning Rich wrote: It's the little metal tip inside where the needle exits. Get that little wrench tool it comes with and tighten it up. Should fix it. The nozzle. Take it off and soak it in a small container, shake the container a bit for some agitation then put it back on. Just be careful when you tighten it. It is way too easy to break the nozzle.
_________________
KKK - Kataas-taasang, Kagalang-galangang Katipunan ng̃ mg̃á Anak ng̃ Bayan
Trade stuff Wants crap
Good Transactions with:
bryce_r
|
| Mon Jul 21, 2014 6:59 pm |
|
|
|
ribbon controller
S7 Royalty
Joined: Mon Feb 12, 2007 2:25 am
Posts: 3494
Location: Earth
|
Re: Airbrush cleaning thanks errybody
appreciate all of the help!!
|
| Tue Jul 22, 2014 6:46 am |
|
|
|
|
Page 1 of 1
|
[ 9 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 56 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
